Crossbow cocking aids and upkeep supplies: rope sleds vs crank cockers, string wax, rail lube, and replacement cocking ropes
Rope sleds and crank cockers: how each one draws the string
A crossbow with a draw weight well over 150 lb is not something most people can pull back by hand, so nearly every owner ends up with a cocking device. The two main classes do the same job in different ways.
A rope cocker (often called a rope sled) hooks onto the string on each side of the rail. A pulley arrangement roughly halves the force you feel at the handles, so a very heavy draw becomes manageable. You set your foot in the stirrup, pull both handles evenly until the string seats in the latch, then unhook. The device is small enough to hang from a belt loop or pack strap.
A crank cocker (such as the crank-style Barnett units and the CenterPoint Power Draw rope-cranking device) uses a gear train and a winding cord. It mounts on the stock, hooks the string, and you turn a handle until the string reaches the latch. Gearing trades speed for a very low, steady effort. Many cranks are detachable and must come off before you shoot. Some crossbows have an integrated crank that stays on the stock. Which style you have is set by the crossbow, not your preference.
Speed, noise and shooting from a treestand or blind
The practical difference shows up in the field. A rope sled is quick: forum owners often point out that a rope cocker is faster for a follow-up shot, because there is no crank to attach, wind, unwind and remove. The cost is that you move your arms and torso in a stand, and a long pull on a small platform is harder than at a bench.
A crank cocker is slower, but the motion is smaller and more controlled. It suits a hunter in a ground blind or a treestand with limited room. It also suits anyone with a shoulder or back problem who can’t pull a rope sled evenly. Winding produces mechanical clicking and cord noise. A rope sled mostly makes a short, sharp hiss as the string slides.
Before you buy, consider where you will actually cock the bow. If you mostly cock at the ground and carry the loaded crossbow up, either device works. If you recock in the stand, test the motion with a safety harness on before the season.
Compatibility checks before you buy a cocking device
A cocking aid is not universal. Check these points against your crossbow’s manual:
- Draw weight and power stroke. The device must be rated for your crossbow’s draw weight. A longer power stroke means a longer pull or more winding.
- Stock and rail shape. Cranks need compatible mounting points. Some crossbows use a proprietary crank or an integrated one.
- Foot stirrup. A rope sled needs a stirrup you can brace against. Bulky boots and a cramped stand change how well you can pull straight up.
- String style. The rope hooks need clearance around string, cables and any string dampeners, which are rubber or silicone silencers.
- Latch and anti-dry-fire. The string must seat fully in the latch before the safety is moved or the device is removed.
A bundled sled is fine if it’s the one the manufacturer specifies for that crossbow. Mixing brands such as TenPoint and Barnett accessories is risky, since the hooks and handles are made for different strings and rails. The most common failure with rope sleds is pulling unevenly. The string then seats off-center, which can shift where the bolt hits and can be dangerous. Look for a model with comfortable handles and clear instructions, then practice cocking on a bench until each pull is level.
String wax: what it does and what to avoid
Crossbow string and cables fray where fibers rub against the rail, the latch and each other. String wax fills the gaps between fibers, repels moisture and cuts friction. It is applied to the string and cables, then worked in with your fingers or a leather scrap until the wax melts slightly and disappears into the strands.
Buy wax made for bowstrings. Household candle wax, paraffin and general-purpose grease can leave residue, attract grit and soften the string. Look for a stick or tube that’s easy to apply in the field. Some combination kits include string wax and rail lube together. These suit new owners, but check that each product is intended for the part it will touch.
Signs that wax is overdue are a dry, fuzzy look on the string, loose fibers, and a rough feel as you slide a finger along it. Fuzz that keeps coming back right after waxing, or a flattened serving, means the string needs inspection or replacement, not more wax. Don’t apply heavy coats on serving, which holds the center of the string against the latch, unless the manufacturer says to.
Rail lube and the flight track
The rail (or flight track) is where the string slides and where the latch or bolt rest may drag. A thin film of rail lube cuts friction, keeps the string’s travel consistent and stops wear on the rail surface and the string’s underside. Dry rails can squeal, shed aluminum or plastic dust, and chew up the string.
Use a product made for crossbow rails, such as the Barnett Slickshot rail lube and wax combination, or the lubricant your crossbow’s maker names. The rule is a thin film: put a drop or two on the string-contact area, spread it with a cloth, then wipe off the excess. Too much lube collects grit and dust, can transfer to the bolt nock and fletching, and makes a mess in a hunting pack.
Avoid mixing wax and oil on the same surface and don’t use general-purpose spray. Check your manual: some crossbows call for a specific lube only on the rail and none on the latch. A lube that works on one rail material may soften another, so follow the manufacturer’s list over a generic recommendation.
Maintenance intervals and replacement cocking ropes
Intervals depend on the crossbow, string material and climate, so treat your manual’s guidance as the first answer. In practice, most owners tie care to use rather than the calendar:
- String wax: apply before the season, after wet or dusty days, and whenever the string looks dry. Check a few times during heavy practice.
- Rail lube: a light application at the start of a range session and again if the string drags or squeaks.
- Cocking device: inspect each time for frayed cord, bent hooks, cracked handles and worn pulleys.
The rope or cord is the part that wears out first. A rope sled’s cord frays at the hooks and pulleys. A crank’s winding cord wears on the spool and at the string hook. Replace it when you see fuzzing, flattened sections or loose strands, and don’t wait for it to snap under load. Buy a replacement rated for your device’s draw weight and matched to its length and diameter. Cord sold by length, such as BCY’s 20 ft cocking cord, only suits a device if it matches the original’s spec. If the crank’s manufacturer sells a replacement rope, use that. A frayed rope that fails mid-pull can drop the string unevenly onto the latch, so keep a spare in your pack. Keep your wax, lube and spare rope together in a small pouch.
Shop crossbow rope cocking sled for Crossbow cocking aids and upkeep supplies: rope sleds vs crank cockers, string wax, rail lube, and replacement cocking ropes
Get Crossbow Rope Cocking SledShop crossbow crank cocking device for Crossbow cocking aids and upkeep supplies: rope sleds vs crank cockers, string wax, rail lube, and replacement cocking ropes
Get Crossbow Crank Cocking DeviceShop crossbow rail lube for Crossbow cocking aids and upkeep supplies: rope sleds vs crank cockers, string wax, rail lube, and replacement cocking ropes
Get Crossbow Rail LubeShop crossbow replacement cocking rope for Crossbow cocking aids and upkeep supplies: rope sleds vs crank cockers, string wax, rail lube, and replacement cocking ropes
Get Crossbow Replacement Cocking RopeRelated guides
- Archery Targets for Bowhunting Practice (bag, foam block, 3D animal, broadhead-rated, and replacement cores/covers)
- Bow Cases for Bowhunting: Hard vs Soft vs Hybrid Compound Bow Cases for Truck Travel, Airline Flights and ATV/Backcountry Transport
- Bowstring Material: Dacron vs Synthetic Fiber Blends
- Choosing the Right Broadhead Grain Weight for Your Setup
FAQ
Is a rope sled or a crank cocker better for hunting?
A rope sled is faster for a follow-up shot and lighter to carry, but it needs a level, even pull. A crank cocker is slower and noisier, but the effort is lower and steadier. In a cramped treestand or blind, a crank often feels easier, while on open ground a rope sled is quicker.
How often should I wax a crossbow string?
Follow your manual, which may express the interval as a time period or a shot count. Between those checks, wax when the string looks dry or fuzzy, and after wet or dusty conditions. Fraying that keeps returning means inspect or replace the string.
Can I use any rope as a replacement cocking rope?
No. Rope has to match the device’s length, diameter and load rating, since it takes the full draw weight of the crossbow. Use the replacement the cocking device’s manufacturer lists, and replace it at the first sign of fraying.