Arrow Inserts, Nocks and Outserts: Matching Components to Your Shaft
Start with the shaft’s inside diameter, not its outside size
Inserts and nocks go inside the shaft, so the number that decides fit is the inside diameter (ID) printed in the maker’s spec table. Hunting carbon falls into three common ID classes: .166 inch (micro diameter, such as Victory VAP), .204 inch (small diameter, such as Easton 5mm shafts) and .246 inch (standard diameter, such as Gold Tip Hunter XT). Easton names its lines by approximate size in millimetres (4mm, 5mm, 6mm, 6.5mm). Those names are product families, not measurements, so read the ID column of the shaft chart before buying parts.
Two IDs that look the same are not automatically interchangeable. Gold Tip lists the Hunter XT at 0.246 ID, while Victory lists its VForce nocks and inserts for a .245 inside diameter. A press-fit nock or a glued insert depends on a few thousandths of an inch of fit, so treat a part as compatible only when the shaft maker’s fitting chart names it for that shaft model. Victory, Easton and Gold Tip each publish component charts by series.
Inserts: thread, weight and which shaft size they fit
A standard insert is glued flush inside the shaft and takes a screw-in point or broadhead. Most hunting inserts use the 8-32 thread. The Easton 5mm HIT insert weighs 16 grains, takes 8-32 points, and Easton lists it as the stock insert for 5mm Axis shafts. For its 6.5mm shafts Easton lists a 6.5mm insert at 23 grains, and for 6mm shafts a 6mm ST RPS insert at 18 grains. Each one is sized to its own shaft family’s ID, so a 6mm insert won’t fit a 6.5mm shaft.
Get Easton 5mm HIT insertInsert weight is also a tuning choice. Gold Tip makes .246 inserts in more than one material, including a 50-grain aluminum insert and a 100-grain brass insert. The brass insert moves 50 more grains to the front of the arrow, which raises front-of-center balance. Extra weight at the tip also makes the shaft act weaker when shot, so check the maker’s spine chart with your total point weight (point plus insert) before you switch.
Half-outs, collars and outserts on small-diameter shafts
Micro and small-diameter shafts often use a component that sits partly outside the shaft, so the tip gets a full-size shoulder and the carbon wall is protected on impact. Easton’s 5mm Half-Out is sized by spine. Easton’s chart lists Half-Out size #1 and Match Grade HIT Collar size #1 for the 5mm size 500, with a 17/64 inch field point outside diameter. Stiffer and weaker spines call for other numbered sizes, so match the size to your exact spine, not just to “5mm”.
Easton lists the Match Grade HIT Collar at 13 to 21 grains. It fits over the shaft end with a HIT insert and takes 8-32 thread 5/16 inch field points. For 4mm shafts, Easton lists a Match Grade Half-Out in steel at 150 grains, made for sizes #3, #4 and #5 only, with 8-32 thread 5/16 inch field points at 75 grains. If your 4mm spine isn’t one of those three sizes, that steel half-out isn’t listed for it.
Nocks: match the series and check the throat
A nock has two fits. The shank has to fit the shaft ID, and the throat has to fit your bowstring’s center serving. Easton lists a 0.103 inch throat for its 6.5MM 3D Super Nock. A throat that’s too tight can affect how the arrow leaves the string, and one that’s too loose lets the arrow slide off the string. So when you change nock families, check that the arrow clips on and hangs from the serving without falling off.
The Easton 5MM X Nock comes pre-installed on Easton’s 5mm Axis shafts and is sold in dozen bags, so a 5mm Axis owner can buy the same nock as a replacement. For Easton’s 6mm FMJ and Aftermath shafts the listed nock is the 6MM H Nock, a separate part that does not fit the 5mm line.
Get Easton 5MM X NockGold Tip Hunter XT shafts take Gold Tip .246 GT Nocks, sold in 12-count packs in several colors. This is the nock family Gold Tip pairs with that 0.246 ID shaft.
Get Gold Tip .246 GT NocksVictory VAP press fit nocks are listed for the .166 inside diameter VAP, VAP TKO and VAP-SS shafts (part ACN166BK-12 is a 12-pack). Victory sells a separate press-fit nock for VForce and VForce TKO at .245. Buy by series, not by color or pack size.
Get Victory VAP press fit nocks8-32 versus Deep Six: the thread that decides your broadheads
Changing inserts can change which broadheads fit. Standard inserts, HIT inserts and most half-outs use the 8-32 thread. Easton’s Deep Six system uses a 6-40 thread for micro-diameter shafts such as the 4mm line. Its threaded portion is narrower and longer, so an 8-32 broadhead or field point will not screw into a Deep Six insert, and a Deep Six point will not seat in an 8-32 insert.
Before buying replacement inserts for a 4mm shaft, write down which thread your current points use, then pick inserts and broadheads on the same thread. If you plan to move between 8-32 and Deep Six, you’ll need a new set of field points and broadheads as well as new inserts.
What to keep on hand for one dozen arrows
Nocks wear out first. Hits from other arrows in a tight group crack them, and a cracked nock should never be shot, because a nock failure on a compound bow can dry-fire the bow. Keep at least one spare 12-pack of your exact nock (for example, the series-specific .246, .204 or .166 nock your shaft maker lists), and keep the same color so your arrows stay matched.
Inserts and outserts are replaced less often, usually after a shaft is cut back or an insert loosens. Keep a few spares of the exact insert model and weight, and for half-outs or collars the numbered size listed for your spine. Changing insert weight across one dozen arrows changes total arrow weight and spine response, and the arrows will no longer group with each other.
Related guides
- Adjustable Youth and Beginner Compound Bows: Choosing by Draw Length and Draw Weight Range
- Archery Targets for Bowhunting Practice (bag, foam block, 3D animal, broadhead-rated, and replacement cores/covers)
- Bow Cases for Bowhunting: Hard vs Soft vs Hybrid Compound Bow Cases for Truck Travel, Airline Flights and ATV/Backcountry Transport
- Bowhunting Backpacks and Field Pack Systems
- DIY Hunting Arrow Building and Repair Tools
- Choosing the Right Broadhead Grain Weight for Your Setup
FAQ
Can I use Gold Tip .246 nocks in a Victory .245 shaft?
Only if one of the shaft makers’ fitting charts lists that combination. Gold Tip states 0.246 ID for its standard shafts and Victory states .245 for VForce, and press-fit nocks rely on very small tolerances. When no chart lists the pairing, buy the nock the shaft maker names for that series.
Will a Deep Six broadhead screw into an Easton HIT insert?
No. Easton’s HIT insert uses the 8-32 thread, and Deep Six uses a 6-40 thread with a narrower, longer threaded section. Match broadheads and field points to the thread of the insert or half-out installed in your shaft.
Does switching to a heavier insert change my arrow’s spine?
The shaft itself doesn’t change, but extra weight at the tip makes the arrow act weaker when shot. Moving from a 50-grain to a 100-grain .246 insert adds 50 grains up front, for example. Check the maker’s spine chart with your new total point weight before you switch a whole dozen.