How to Measure Draw Length and Choose Draw Weight for a Hunting Bow
Get a starting draw length from your wingspan
The Archery Trade Association’s quick method uses your wingspan. Stand with your back to a wall, arms straight out at shoulder height and palms facing forward. Have someone measure in inches from one middle fingertip to the other, then divide by 2.5. A 70-inch wingspan works out to 28 inches of draw length, and a 67-inch wingspan works out to 26.8, which you would try at 27.
Measure two or three times and round to the nearest half inch, because many compound cams and modules adjust in half-inch or one-inch steps. This number is only an estimate. Shoulder width, neck length and the anchor you use all change the real figure. Use it to set a bow you are borrowing or to narrow down the draw-length ranges you shop, then confirm it at full draw before anyone cuts arrows.
Confirm the number at full draw
The ATA defines draw length as the distance from the nocking point on the string to the pivot point of the grip, plus 1.75 inches. A pro shop checks it with a draw length measuring arrow: an uncut shaft with inch marks along it. You draw it on a light bow, settle into your anchor, and someone reads the mark at the front of the riser. Measure with the release you will hunt with. A wrist-strap release, a handheld release and fingers on a D-loop each put your hand in a slightly different place, so a measurement taken with fingers on the bare string can be off for a release shooter.
Get draw length measuring arrowAt full draw the body shows a wrong setting too. If the draw is too long, the bow-arm elbow locks or bends past straight, the string slaps the forearm, and the anchor slides back behind the jaw. If it is too short, the bow arm bends sharply, the shoulders feel cramped, and the string never reaches the tip of your nose. Change the draw length in small steps and shoot several ends at each setting before you judge it.
Set draw length on a compound bow
Most compound bows change draw length at the cams. Some have rotating modules that move between lettered or numbered positions with an Allen key. Others need a different module for each length, or a bow press to remove the string. Owner manuals for bows with rotating modules say both cams must be set to the same position. One cam left on a different setting throws the bow out of time.
Bows with a very wide adjustment range fit a growing archer or several shooters in one household. The Diamond Infinite Edge Pro adjusts from 13 to 31 inches of draw length and from 5 to 70 pounds, and its owner manual says it ships set to 26 inches of draw. On any bow, read the module chart in the manual for your model. Settings at the ends of a range often have a rougher draw cycle or a different let-off than the settings in the middle.
Get Diamond Infinite Edge ProPick a draw weight you can actually hold
Draw weight is the peak force needed to pull the string through the cam’s hump, measured in pounds. Here is a shop test that matches hunting conditions. Sit on a chair with your feet off the floor, hold the bow arm level at the target, and draw without lifting the bow toward the ceiling. Hold at anchor for 20 to 30 seconds, let down slowly, and repeat five times. If you have to point the bow up to start the draw, or you shake before the hold ends, lower the weight. Cold muscles in a treestand at dawn are weaker than warm ones at the range.
Let-off sets the weight you hold, not the weight you pull. A 60-pound bow with 80 percent let-off holds at 12 pounds, but you still have to get through the full 60 to reach it. The law sets a floor as well. Pennsylvania requires at least 35 pounds of draw weight for archery deer seasons. Maine requires 35 pounds for deer and 45 pounds for moose. Check your state’s current hunting digest before you set the bow lower.
Adjust and verify draw weight
Compound draw weight is changed at the limb bolts. Turn clockwise to add weight and counterclockwise to reduce it. Hoyt says to turn the top and bottom bolts by equal amounts. Many adult hunting bows are sold in 10-pound windows, such as 50 to 60 or 60 to 70 pounds. Each manual gives the most the bolts may be backed out from fully tight. Past that point the bolt has too little thread holding the limb, so you need lighter limbs, not more turns.
Counting bolt turns does not tell you the actual weight. A digital bow scale does. Hook it at the nocking point, draw to full draw, and read the peak value the display holds. Write that number down at your confirmed draw length. On a recurve, the weight printed on the limb is measured at 28 inches, so a shooter who draws longer or shorter is pulling more or less than the label says.
Get digital bow scaleCarry both numbers into arrow selection
Arrow spine charts take two inputs: arrow length and peak bow weight. Easton measures correct arrow length from the bottom of the nock groove to the cut end of the shaft. The point and insert are not included. Arrow length is not your draw length. A hunting arrow has to stay far enough past the rest that broadhead blades stay clear of the riser and your hand at full draw.
Easton’s hunting shaft chart assumes a bow with an ATA speed rating of 301 to 340 feet per second, screw-in 100-grain points and a release aid. Its bow-weight columns come in 5-pound bands, such as 57 to 61 pounds. Change the bow weight you look up when your setup differs: heavier points make the arrow act weaker, so a heavier tip moves you to a stiffer column. A lower spine number means a stiffer shaft, so a 330 is stiffer than a 500. Enter your measured peak weight and your cut length, read the size where the row and column meet, and check it against the arrow maker’s own chart for the shaft you plan to buy.
Related guides
- Adjustable Youth and Beginner Compound Bows: Choosing by Draw Length and Draw Weight Range
- Archery Targets for Bowhunting Practice (bag, foam block, 3D animal, broadhead-rated, and replacement cores/covers)
- Arrow Inserts, Nocks and Outserts: Matching Components to Your Shaft
- Bow Cases for Bowhunting: Hard vs Soft vs Hybrid Compound Bow Cases for Truck Travel, Airline Flights and ATV/Backcountry Transport
- How to Match Arrow Spine to Your Hunting Bow
FAQ
Does a shorter draw length make a bow slower?
Yes. A shorter draw gives the string less distance to push the arrow, so less energy goes into it. ATA speed ratings are measured at 30 inches of draw, 70 pounds and a 350-grain arrow, so a shorter or lighter setup shoots slower than the rating on the box. Never lengthen your draw past what fits you to gain speed. It costs you accuracy.
Can I tell my draw weight from the limb bolts alone?
Only roughly. Pounds per turn varies by limb and cam, and the label usually shows only the peak of the limb’s range. Use a digital bow scale at your actual draw length, and use that reading in spine charts.
How often should a young archer’s draw length be rechecked?
Recheck the wingspan and the full-draw fit whenever the archer grows noticeably or starts having trouble reaching the anchor. On bows with rotating modules this is a small adjustment. Arrows cut for the old setup may be too short or too weak after a large change, so check the arrow length and the spine chart again.